Add Favorite Set Homepage
Position:Home >> News

Products Category

Products Tags

Fmuser Sites

How to Eliminate Noise on AM and FM Receiver

Date:2016/4/25 15:30:23 Hits:



"The radio noise problem is as old as radio itself. Unfortunately it is getting worse as technology steadily progresses and more man-made electronic products hit the shelves. This is a direct result of mainly consumer products that generate an increasingly higher noise level. As the use of transmitters, receivers and communication devices increases, so do the disruptions in signal reception. As a rule, FM receivers are less affected by crackling noises than AM receivers. Conversely, AM radio is not as susceptible to the signal reflection phenomena. ----- FMUSER."



Content

Basic recognition
Can Unwanted Voices or Sounds be Heard on Your AM or FM Radio?
How to Locate the Entry Point of an Unwanted Signal
Interference Specific to AM Radio
How to Eliminate Noise on an AM Receiver
Interference Specific to FM Radio
How to Eliminate Noise on an FM Receiver


Basic recognition
● RF Waves
Radio waves are a form of electromagnetic radiation, like light, except at a lower frequency and not visible. They are non-ionizing radiation, so they do not carry enough energy to affect chemical bonds but the effects of magnetism on biological systems could use further study. Using radio waves to transmit signals was first developed back in the 1870s, and later helped transform society. 

The sound waves of a human voice vibrate at a range of 300 to 3000 cycles per second or Hertz (Hz), a unit named after German physicist Herman Hertz, who studied the production and reception of radio waves. A microphone converts these sound vibrations into electrical energy. 

The length of the antenna required to transmit a signal is related to the wavelength. Directly transmitting frequencies in the audio range would have long wavelengths requiring a humongous antenna and lots of amplification. Instead, an oscillator generates a carrier wave with a higher frequency resulting in a shorter wavelength and more manageable antenna. The carrier wave is also of a constant frequency and amplitude.

Basic Checks for AM/FM Interference
1. Check Connections
2. Disconnect all accessories
3. Perform the equipment substitution test
4. Check with Neighbours

See Also: >>What is the Difference between AM and FM? 

Identify the Source of the Interference
First, determine whether the source of the interference is internal or external to the radio itself.The interference may be caused by atmospheric conditions, and in that case, all you can do is wait for conditions to change. Real interference and improper tuning of the desired station can have the same effect. Changing the orientation of the radio can maximize reception of the desired signals. In some cases, an outdoor antenna also helps.


>>Back to the top


Can Unwanted Voices or Sounds be Heard on Your AM or FM Radio?
When you hear unwanted voices or sounds, the equipment is receiving interference from GRS transmitters (better known as CB radios), from amateur radio transmissions, or from other radio services with a transmitter located nearby. The interference thus appears intermittently, as the signals are being transmitted.

This kind of interference, known as audio rectification, is usually caused by the receiver. With this phenomenon, an electronic circuit, usually an amplifier, is suddenly affected by strong unwanted outside radio signals. If the equipment is surrounded by an intense radio signal, the circuit wiring or the system components may act as antennas and pick up an unwanted signal. This is not necessarily due to a technical fault in the transmitter. The entry point of the unwanted signal must be located, which can be done by disconnecting all accessories to isolate the culprit.

Check your neighborhood for transmitter antennas in order to identify the potential source of the interference, then try to find a solution with the person responsible. Filters, shielding or grounding may be required.

How to Locate the Entry Point of an Unwanted Signal
Accessories and Speaker Wires
A. Disconnect all accessories connected to the radio such as auxiliary speakers, turntable, interconnecting stereo system cables, tape deck and compact disc player. Reconnect each cable one at a time to identify the accessory that is the source of interference. Proper grounding and good connections between the accessory and the equipment sometimes eliminate the interference. If necessary, ask a technician to do the installation or modifications.


B. If the interference persists after all the accessories have been disconnected, the problem may lie between the volume control circuit and the speakers. If varying the volume has no effect on the level of the offending radio signal, the entry is likely the speaker wiring. To verify this potential entry point, disconnect the speaker wires from the amplifier and listen for the interference with the headphones. If the problem disappears, any unshielded speaker wires should be replaced with shielded audio cable.


See Also: >>Amplitude Modulation in RF: Theory, Time Domain, Frequency Domain


● Receiver Overload

When station A is tuned in, the sound from station B can be heard in the background. (It may actually drown out station A.) This can occur only when the signal received from station B is much stronger than that from station A, because station B is closer. 


The signal from station B is either intercepted by the antenna or picked up directly by the electronic circuits inside the receiver. 


If station B is new to the neighbourhood, the broadcaster will help you. Repointing the antenna may eliminate reception of the strong undesired signal if the desired signal is not too weak.


>>Back to the top


Interference Specific to AM Radio

The technology behind the AM broadcast signal is very out-dated as far as current technology is concerned, not to mention that the AM broadcast band is located in the very vulnerable medium wave frequency band. 


● Interference from electrical sources

Some electrical equipment or installations in the home may cause interference.


To identify or discover certain other types of electrical interference not described below, it may be necessary to carry out the breaker test.


● Interference from fluorescent and neon lights

Fluorescent lights produce a kind of steady buzz when they are turned on, while neon lights can trigger short clicks. Neon lights contain gas under pressure that emits bright light when traversed by an electrical charge. Moving the radio further away or replacing the tubes or fixtures may solve the problem. Certain repairs can also be made by a technician to eliminate the problem.


● Motors

Many motors can cause interference on AM radios, including those in electric shavers, sewing machines, vacuum cleaners, blow dryers and mixers. The sound of the interference is similar to that of the device causing it. Since these devices are operated only for brief periods, it is often impractical to try eliminating the interference.


Nevertheless, a filter may be added to the device or to the radio.


See Also: >>How To Load/Add M3U/M3U8 IPTV Playlists Manually On Supported Devices


● Electrical contacts

Some electrical contacts can be the source of interference that takes the form of small staccato sounds or continuous crackling. After a while, electrical contacts on some thermostatic devices become dirty or pitted causing sparking when the electrical current passes through. Heating pads, electric blankets, aquarium heaters and doorbell transformers can cause this type of interference. The breaker test will help locate the source so it can be replaced or repaired.


● Dimmer switches

The radio crackles continuously at a fairly high pitch that can be heard across the entire AM band. Conduct the breaker test to find the faulty switch, and replace it with a better quality dimmer switch equipped with a filter. The metal boxes that cover certain dimmer switches also act as excellent shielding.
 

● Oil or gas burners

The sound from this type of interference is distinguished by intermittent buzzing lasting anywhere from a few seconds to a few minutes. This interference is caused by the spark created to light the pilot flame in this equipment. Call in a qualified technician to repair or replace the ignition system.


● Electric fences

This equipment primarily affects AM radio. The interference caused by an electric fence resembles a “tick” repeated at regular intervals of one or two seconds. By nature, this type of interference is found only in rural regions. 






If the interference persists after the electric fence has been disconnected, the problem lies in the control box. If the interference occurs only when the electric fence is operating, the installation of the electric wire should be checked. A damaged section of wire or branches or shrubs rubbing against the wire are two possible sources of the interference.


>>Back to the top


● Industrial, scientific or medical (diathermic or heating) equipment

Do you hear a cyclical vibrating buzz or hum in your radio? Some radio frequencies are used to produce heat in the food, plastics and wood industries and can cause this type of interference. Diathermy is used for medical purposes. 


Check to see if this equipment is located in the neighbourhood. In most cases, corrective measures must be applied to the equipment causing the interference. Contact officials in the institution where the equipment is located.


See Also: >>What is QAM: quadrature amplitude modulation 


● Intermodulation

The radio is emitting a mixture of voices and music resulting from the mixing of two or more radio stations. In the presence of strong radio waves, corroded metal contacts or connections can act as detectors and generate unwanted signals that affect receivers in the surrounding area. 






This is more precisely referred to as external rectification. If the interference affects a broad range of frequencies, the source is often located very close to the most powerful transmitter, on the antenna itself, on the guy wires or very close to the broadcast station. The corroded contact must be identified so it can be cleaned or insulated. A word of caution: there may be more than one source of interference at a single location. The level of interference will decrease as sources are eliminated. Generally, this type of interference disappears when it rains. Involved radio stations will help you identify and eliminate this type of problem.


>>Back to the top


● Weak signal

Sound on the radio is weak. There is a whistling or buzzing sound in the background. In addition, it is difficult to tune in the desired station, and adjacent stations can drown out its signal. Broadcasting stations are assigned specific coverage areas. 




Outside the designated area, stronger signals from neighbouring stations will overwhelm weaker signals, because the frequency of the closer station will cover the more distant signals. Changing the orientation of the radio may maximize reception of the desired signal. If the two stations are broadcasting from different directions, an outdoor directional antenna can amplify the weak signal. Whenever an attempt is made to pick up a station from a point outside its broadcast area, a number of interference problems can appear.


See Also: >>Frequency Modulation Advantages & Disadvantages


● Nighttime interference

In the evening, does the sound of the desired station fade in and out, and do one or more other stations occasionally drown it out? This type of interference is linked to the propagation characteristics of AM radio signals. 


At night, transmitters located hundreds or even thousands of kilometres away can disrupt reception of stations in the area. Changing the orientation of the AM radio should improve reception. On the other hand, this solution may prove temporary, because ongoing variations in signal propagation during the night are apt to change reception conditions unpredictably.


>>Back to the top


● Interference from electrical power lines

This type of disruption sounds like sizzling, sparking, intermittent or continuous crackling and appears and varies in intensity with weather conditions (dry or damp weather, wind). 


Additionally, if the result of the breaker test indicates that the source is outside the home, there is a good chance the interference is caused by faulty components in electrical power lines in the surrounding area. 


Contact your electrical utility to resolve the problem.


● If the problem persists

The source of the interference is probably outside the home. Check with your immediate neighbours. The location where the interference is most intense is very likely to be the source of the disruption. Ask your neighbours to perform the breaker test in their homes to isolate the faulty device. An appliance or electrical device rarely causes interference extending beyond a few houses. This should help you find the source of the interference. The interference may also be caused by electrical power lines. The power grid supplying the neighborhood may be the source of the interference.


>>Back to the top


How to Eliminate Noise on an AM Receiver

Some of these are sources of noise that even the best, highest dollar receivers and the best antenna systems in the world cannot overcome and should be momentarily turned off while listening. If you are an apartment dweller, chances are you have a neighbor right next door that has a computer or floursecent light right behind the wall next to you. 


If this is the unfortunate situation you are in, try speaking to your neighbor and see if you can come up with some type of solution. You can always change to another room. If that doesn't work, you can always purchase a quality FM Transmitter, place your receiver at the point of least noise and transmit the signal across your apartment to your radio..... This is always a possibility and in most cases eliminate your neighbor problem. As far as noise goes anyways.

See Also: >>AM receiver vs FM receiver | Difference between AM receiver and FM receiver 

Also, a lot of you have hear in the news, mentions of digital radio on the AM and shortwave broadcast bands. It is impossible, even for digital radio to get rid of your radio noise. Digital is a 1s and 0s thing. Basically if you have noise, you get a Big 0.... nothing at all. Your radio will simply revert back to analog mode and you will be stuck with enjoying the same high-quality buzz and hum that you have enjoyed all these years.... (smirk)

So, to summarize, get rid of your noise souce and get the full potential quality audio from your receiver.


>>Back to the top


Interference Specific to FM Radio

● Weak signal

Have you been unable to tune in your favourite FM station since a new station went on the air on a neighbouring frequency? FM stations each have their own specific coverage area. Although some listeners living outside this area can still pick up the station, a station with a stronger signal may override more distant signals. A directional antenna can boost the weaker signal, provided of course, the two stations are not located in the same direction. A difference of 90 to 120 degrees is ideal.


● Multiple signals

In a moving car, the receiver may give off a 'fut-fut-fut sound'. This type of interference is common when signals are coming from more than one direction, or when they are reflected off buildings or other structures. Depending on how you travel, signals come and go, and sometimes disappear in a cacophony of noise.


Reflection is a characteristic specific to FM signals. When the receiver allows, switching from stereo to mono mode can sometimes improve reception.


>>Back to the top


How to Eliminate Noise on an FM Receiver
Many radio transmitters use frequency modulation (FM) to disseminate broadcasts. FM waves are less susceptible to noise and static than amplitude modulation (AM) waves. However, the performances of FM receivers are altered by the presence of other electronic devices. When other devices are too close to FM tuners, white noise or static pollutes the radio broadcast. To fix this problem, try these two solutions.

● Keep any cell phones or two-way radios at least 20 feet from an FM receiver. Cell phones, even when not in use, send out pings that are picked up by FM receivers. As an experiment, place a cell phone next to an FM receiver for a few minutes and listen to when the pings are sent.

● Choose a station and adjust the dial to the setting if you are using an analog radio. Use very small adjustments to remove the static and noise from the station. During the day, an FM signal will change due to atmospheric-pressure changes; this requires the user to make tiny adjustments.

● Add a larger external antenna to the receiver. Many FM receivers include screw-down attachments for long antenna wires. Screw the antenna wire into the receiver and attach the wire to a wall or run it out of a window to improve reception, thus reducing static and noise.



>>Back to the top




If you want to purchase any FM/TV euipments for broadcasting, please feel free to contact us by Email: [email protected].?

Leave a message 

Name *
Email *
Phone
Address
Code See the verification code? Click refresh!
Message
 

Message List

Comments Loading...
Home| About Us| Products| News| Download| Support| Feedback| Contact Us| Service

Contact: Zoey Zhang    Web: www.fmuser.net

Whatsapp/Wechat: +86 183 1924 4009

Skype: tomleequan     Email: [email protected] 

Facebook: FMUSERBROADCAST     Youtube: FMUSER ZOEY

Address in English: Room305, HuiLanGe, No.273 HuangPu Road West, TianHe District., GuangZhou, China, 510620    Address in Chinese: 广州市天河区黄埔大道西273号惠兰阁305(3E)